Секция с навигацией, мета информацией, заголовком и контентом

How to check the power cable after installation: insulation, integrity, connections and protocol

  • calendar-icon
    31-10-2026, 2026
  • user-icon
    Alexey Krasikov
  • clock-circle-icon
    2 минуты
article preview photo
article preview photo

Testing Sequence

Testing of an installed cable line is performed in a strict sequence: visual inspection, checking conductor integrity and phase identification, insulation resistance measurement, connection inspection, additional tests (if required for the given voltage class), and preparation of the test report. Violating the order leads to missed defects or equipment damage during subsequent measurements.

All work is performed on a de-energized and grounded line. Before testing begins, the project documentation and equipment data sheets are reviewed, and the instruments are checked for operability. The scope of tests depends on the line voltage and insulation type: for cables up to 1 kV and above 1 kV it differs. The standards and scope of tests are established by the Electrical Installation Code of the Republic of Kazakhstan, paragraph 29 “Power Cable Lines.”

Visual Inspection

Inspection begins with checking the route: the cable must not have mechanical damage to the sheath, kinks, or signs of overheating. At wall and floor penetrations, the integrity of the sleeves and sealing is checked. Terminations and joints are inspected for cracks, drips, and contamination. Particular attention is paid to sections where the cable was under tension during pulling: this is where microcracks most often occur, which are not immediately visible but appear during testing. Installation rules and typical installation errors affecting the line condition are discussed in the material power cable installation: PUE standards, methods, and mounting.

Checking Conductor Integrity and Phase Identification

Checking conductor integrity and phase identification is performed after installation is complete, after joints are re-made, or after conductors are disconnected. The purpose of the check is to ensure that all conductors are intact and that phase markings at both ends of the line match. For cables up to 10 kV, conductor integrity is checked with a megohmmeter: the resistance between the beginning and end of each conductor is measured. The resistance must be close to zero; a break gives an infinitely large value.

Phase identification is performed after voltage is applied: the correspondence of the cable phase at one end to the same-name bus phase at the other end is checked. For 6 and 10 kV lines, voltage detectors with an additional resistance are used. A phase identification error leads to a short circuit when switching to parallel operation. If the integrity check reveals an elevated conductor resistance, this may indicate a conductor defect or poor contact in the joint. The methodology for measuring and evaluating conductor resistance is described in the article cable conductor resistance: how to measure and what the result shows.

Insulation Resistance Measurement

Insulation resistance measurement is a mandatory check for cable lines up to 1 kV. It is performed with a 2.5 kV megohmmeter. For power cables up to 1 kV, insulation resistance must be at least 0.5 MΩ. For cables above 1 kV, insulation resistance is not standardized, but the measurement is performed to assess insulation condition and compare with previous results. The measurement is taken before and after high-voltage testing of the cable, if such testing is provided.

Before measurement, the cable is de-energized, the absence of voltage is verified, and the conductors are discharged to earth. The resistance is measured between each conductor and the remaining conductors connected to the sheath, as well as between conductors. Readings are taken 60 seconds after voltage is applied, when the absorption current stabilizes. After each measurement, the conductor is discharged to earth. The detailed methodology, selection of megohmmeter voltage for different cross-sections and cable types, and evaluation of results are given in the material cable insulation resistance measurement with a megohmmeter: procedure and results.

Checking Connections, Joints, and Lugs

Connections are the most vulnerable element of a cable line. After installation, the quality of bolted contact tightening and lug crimping is checked. The PUE requires selective checking of contact tightening and opening of 2–3% of connections. The voltage drop or resistance across a contact connection must not exceed the voltage drop across an equal length of intact conductors by more than 1.2 times. For contacts carrying more than 1000 A, full inspection is recommended.

Crimped connections are checked by visual inspection and contact resistance measurement. The lug must not have cracks, misalignment, or signs of overheating. Joints are inspected for tightness and absence of damage. If a connection is made in violation of technology, contact resistance increases, and local overheating occurs under load. Requirements for joint installation and conductor termination are collected in the article power cable connection: joints, termination, and installation.

Additional Tests by Voltage Class

For cables above 1 kV and up to 35 kV, the Electrical Installation Code of the Republic of Kazakhstan provides for high-voltage DC testing. The test voltage values and application duration are established by Table 97 of Appendix 1 to the PUE RK. During testing, the nature of the leakage current change is monitored. The cable is considered to have passed the test if no breakdown occurred, there were no sliding discharges or leakage current surges, and no increase after reaching a steady value.

For 110 kV and above cables, the scope of tests expands: determination of conductor DC resistance, measurement of electrical working capacitance, checking current distribution across single-core cables, inspection of anti-corrosion coating, and other checks are added. For cables with rubber insulation up to 1 kV, high-voltage testing is not performed. The scope of tests for a specific line is determined by the project and cable type. If a breakdown or deviations are detected during testing, damage localization methods are used, described in the article how to locate power cable damage: main diagnostic methods.

Test Table

Table 1. Power cable tests after installation
Test Instrument / method What it reveals
Conductor integrity and phase identification Megohmmeter, voltage detector with additional resistance Conductor break, mismatch of phase markings
Insulation resistance 2.5 kV megohmmeter Moisture, aging, mechanical damage to insulation
Bolted contact tightening Torque wrench, selective opening of 2–3% of connections Loose contact, high contact resistance
Crimping quality Visual inspection, contact resistance measurement Loose contact, cracks, lug misalignment
High-voltage test (above 1 kV) DC test set Insulation breakdown, sliding discharges, leakage current increase
Conductor DC resistance (110 kV and above) DC bridge Undersized cross-section, conductor defects

Actions for Deviations

If insulation resistance is below 0.5 MΩ for a cable up to 1 kV, the condition of the terminations is checked: contamination, moisture, cracks. The ends are wiped, dried, and the measurement is repeated. If resistance remains low, the insulation is defective — the cable must not be operated without repair or replacement of the section.

If a breakdown occurs during high-voltage testing, the cable is considered to have failed the test. The breakdown location is localized by reflectometry, acoustic, or induction methods. After localization, a decision is made to repair the joint or replace the section. If contact resistance of a connection is elevated, the contact is reworked: retightened, the lug replaced, or re-crimped. A repeat check is performed after the defect is eliminated.

Preparing the Test Report

Test results are documented in a report. The report states: line designation, cable grade and cross-section, length, network voltage, temperature and humidity during testing, instruments used with numbers and calibration dates, results of each measurement, and a conclusion on compliance. The report is signed by the executor and the work supervisor. Without a report, the cable line cannot be submitted for commissioning.

Acts of hidden work inspection are attached to the report if the cable was laid in the ground or behind structures. For lines above 1 kV, high-voltage test reports and conductor resistance measurement reports are additionally attached. Report forms may differ between organizations, but the data composition must comply with the requirements of the PUE RK and project documentation.

Safety Requirements

All tests are performed with voltage removed. Before work begins, the absence of voltage is verified with a detector, and grounding is installed on the cable conductors. High-voltage testing is performed under a work permit by a team of at least two people with qualification groups IV and III. The test area is fenced off, and warning posters are displayed.

After each measurement, the conductor is discharged to earth using a grounding rod. Residual charge on the conductor is life-threatening. When working with a 2.5 kV megohmmeter, dielectric gloves and tools with insulating handles are used. Instruments must be calibrated, and test leads must have sufficient insulation.

Typical Mistakes

Measuring insulation resistance without discharging conductors. Residual charge distorts the result and is dangerous for personnel. Discharge to earth is performed after each measurement.

Checking insulation at negative temperatures. Frozen water in insulation is not detected, the cable is deemed serviceable, and after thawing the resistance drops. Measurements are taken at positive temperatures.

Selective connection inspection without opening. Visual inspection does not reveal a loose contact. The PUE requires opening 2–3% of connections and checking tightening.

Using an uncalibrated megohmmeter. Instrument error is not accounted for, and the result is invalid. The instrument must have a valid calibration certificate.

Missing report. Without documentary confirmation of results, the line cannot be commissioned. The report is prepared based on the results of all checks, not just insulation.

FAQ

What insulation resistance is considered normal for a power cable up to 1 kV?

At least 0.5 MΩ. The measurement is performed with a 2.5 kV megohmmeter. For cables above 1 kV, insulation resistance is not standardized, but the measurement is taken to assess condition.

Is high-voltage testing of the cable after installation mandatory?

For cables above 1 kV and up to 35 kV, high-voltage DC testing is mandatory under the PUE RK. For cables up to 1 kV with rubber insulation, testing is not performed; for other cables up to 1 kV, testing may be replaced by insulation resistance measurement with a 2.5 kV megohmmeter.

What is checked during conductor integrity and phase identification?

The integrity of each conductor and the matching of phase markings at both ends of the line. The check is performed after installation, joint re-making, or conductor disconnection. For cables up to 10 kV, integrity is checked with a megohmmeter and phase identification with a voltage detector.

How many connections are opened during contact inspection?

The PUE requires selective tightening checks and opening of 2–3% of connections. For contacts carrying more than 1000 A, full inspection is recommended. The voltage drop across a contact connection must not exceed the voltage drop across an equal length of intact conductors by more than 1.2 times.

What to do if insulation resistance is below normal?

Check terminations for contamination and moisture, wipe and dry them, and repeat the measurement. If resistance remains low, the insulation is defective. The cable must not be operated without repair or replacement of the section. The damage location is localized by reflectometry or acoustic methods.

Sources

  • Electrical Installation Code of the Republic of Kazakhstan 2015, as amended by Order of the Minister of Energy of the Republic of Kazakhstan No. 340 dated 31.10.2022 — paragraph 29 “Power Cable Lines,” clause 311 — in force — IPS “Adilet,” adilet.zan.kz — scope of tests, insulation resistance standards, integrity and phase identification checks.
  • GOST 31996-2012 “Power cables with plastic insulation for rated voltage 0.66; 1 and 3 kV. General specifications” — in force — Table 14 — acceptance tests: conductor resistance check, insulation resistance check, voltage test.
  • GOST 3345-76 “Cables, wires and cords. Method for determining electrical insulation resistance” — in force — measurement method, requirements for equipment and test conditions.
  • IEC 60364-6:2016 “Low-voltage electrical installations — Part 6: Verification” — in force — IEC — minimum insulation resistance values, verification methodology.
  • Rules for Technical Operation of Consumer Electrical Installations — section 29 — in force — requirements for the frequency and scope of cable line tests.
Выберите свой город
Выберите язык
RU UA FR EU OT RU RU UA FR EU OT RU